Most ordered
Capsaicin rodent tape
The Japanese-made tape Honda sells as part 4019-2317, on a 20 metre roll. It works on any vehicle.
- Use
- Wiring rodents can reach
- Pack
- 20 m (65.6 ft) roll
- Good to know
- Same tape as Honda 4019-2317
Price $62.99
Fuse taps, relays, harness tape, cable ties, switches and the small parts that make an install clean and reliable: the same supplies we use on our own installs at our Markham shop. Pick a job in the kit builder and it lists what you need, or shop by category. Flat $10 shipping in Canada, free on orders over $200.
A fuse protects the wire, so every power wire you add needs one, rated no higher than the wire can carry. A fuse tap does it at the fuse box: the car's original fuse goes in one slot and your new circuit's fuse in the other. Not sure which tap your fuse box takes? Our fuse identifier shows each type at true size.
Remote starter and alarm outputs, and small toggle switches, are made to switch a little current. For lights, horns, fans and door locks, let them trigger a relay and let the relay carry the load. A relay harness turns a bare relay into a plug-in part with colour-coded leads.
Tesa 51608 fleece tape is what we wrap interior harnesses in: it tears by hand and stops rattles. Tesa 51036 PET cloth tape handles engine-bay heat and abrasion, and Tesa 51618 matches the factory tape on BMW and Mercedes. Keep electrical tape, like 3M Super 33+, for covering joints rather than wrapping looms.
Pack DUM-DUM butyl round wires that pass through a grommet or a drilled hole, use a waterproof connector where a joint lives outside the cabin, and put anti-corrosion gel on connections that will see moisture.
Double-sided tape lets go of textured dash plastic on the first hot day unless you wipe the surface with 3M 4298 adhesion promoter first. Mount modules on hook and loop so they lift off for service, and tie new wiring to existing looms every few inches with cable ties.
Everything we keep on the shelf for wiring jobs, sorted the way installers look for it.

Best seller1 to 120 amp, 12 and 24 volt, timer relays and plug-in harnesses.
17 products






Free tool
Pick the job and we'll list the supplies we'd use, all from this store. Untick what you already have, change quantities or fuse types, and add the rest to your cart in one go.
What's the job?
Power a dash cam from the fuse box instead of the lighter socket, with the cable hidden behind the trim. These are the supplies around your camera's own hardwire cable.
You also need the hardwire cable made for your dash cam. It isn't in this list: find it on your camera's page or in Dash Camera Power Cables.
Pick the type your fuse box takes. Fuses aren't included: the car's fuse goes in one slot, one for the camera in the other.
Details for Add-a-Circuit Fuse Tap — ATO/ATC, Mini, Low-Profile Mini, Micro2 & Micro3$6.99 CAD
Our DCINSTALLKIT: hardware to power a dash cam from the fuse box instead of splicing into wiring, and it can be removed later.
Details for Lockdown Security DCINSTALLKIT Dashcam Hardwire Install Kit$14.99 CAD
ATO/ATC fuses, 3 to 20 amp, for an ATO/ATC tap.
Details for Littelfuse ATO/ATC Blade Fuses — 5 Pack (3 A to 20 A)$1.99 CAD
Micro2 fuses, for a Micro2 tap.
Details for Littelfuse Micro2 (ATR) Blade Fuses — 10 Pack (5 A to 30 A)$14.99 CAD
Micro3 fuses, for a Micro3 tap.
Details for Littelfuse Micro3 (ATL) Blade Fuses — 10 Pack (5 A to 15 A)$14.99 CAD
Wrap the cable where it runs behind trim, so it can't rattle. Tears by hand.
Details for Tesa 51608 Fleece Harness Tape (Tearable) | Interior Use | 3/4" Width x 82 Foot Length Roll$13.99 CAD
Tidy the spare cable under the dash. 1000 pack.
Details for 4" Wire Ties WT-4B | 1000 Pack$14.99 CAD
Tuck the cable into the headliner and pillar trim without marking it.
Details for LY-TPS5 Plastic Panel Puller and Scraper Set | 5 Piece Set$29.99 CAD
Your kit
Flat $10 shipping in Canada, free on orders over $200.
Rather we did it? Dash cam installation at our Markham shop, from: Front Dash Camera Installation $150 CAD
Give a 12 volt accessory its own fused circuit from the fuse box, with a switch if you want one. Anything drawing more than 12 amps should go through a relay: see Wire a relay.
Leave airbag, ABS and engine management fuses alone, and fit the fuse tap the right way round: the fuse tap page shows how to check.
Pick the type your fuse box takes, and fit a fuse rated for the accessory in its second slot.
Details for Add-a-Circuit Fuse Tap — ATO/ATC, Mini, Low-Profile Mini, Micro2 & Micro3$6.99 CAD
Switch the accessory on and off directly, up to 12 amps. Pre-wired with 6 inch leads.
Details for MTSW-6 Mini 12 Amp Toggle Switch (Pre-Wired)$6.99 CAD
Wiring from the battery instead? Fuse the wire close to the battery with this 14 gauge inline holder.
Details for FH-14ATC Fuse Holder$2.49 CAD
ATO/ATC fuses, 3 to 20 amp, for an ATO/ATC tap or the inline holder.
Details for Littelfuse ATO/ATC Blade Fuses — 5 Pack (3 A to 20 A)$1.99 CAD
Cover the joints. Stays stuck in the cold.
Details for 3M Super 33+ Electrical Tape, 75 Feet, 22.86 Meter Roll$15.98 CAD
Wrap the new wiring so it can't rattle.
Details for Tesa 51608 Fleece Harness Tape (Tearable) | Interior Use | 3/4" Width x 82 Foot Length Roll$13.99 CAD
Secure the new wire along existing looms. 1000 pack.
Details for 6" Wire Ties WT-6B | 1000 Pack$24.99 CAD
Self-adjusting stripper for 10 to 22 AWG.
Details for LY-731 Wire Stripper (Self Adjusting)$34.99 CAD
Your kit
Flat $10 shipping in Canada, free on orders over $200.
Rather we did it? We wire accessories at our Markham shop: Book an installation
Switch a heavy load with a small trigger: lights, a horn, a fan or door locks. The relay carries the current, so your switch or module output doesn't have to.
Our everyday relay: 12 volt, 5-pin SPDT, 30/40 amp.
Details for Suntech SEM-1417 SPDT 12 Volt 30/40 Amp Relay | SPDT$5.99 CAD
Wiring under the hood or outside? This waterproof 30 amp relay comes with its own harness, so untick the RH-200.
Details for InstallBay IBW-E123H 12 Volt 30 Amp Waterproof Relay with Harness | SPDT Single Pole Dual Throw$19.99 CAD
The plug-in socket for a standard 5-pin relay, with colour-coded leads.
Details for Suntech RH-200 Single Relay Harness$2.99 CAD
Fuses the relay's power feed, close to where you take the power from. 14 gauge.
Details for FH-14ATC Fuse Holder$2.49 CAD
A fuse for the holder: rated for the load, and no higher than the wire can carry.
Details for Littelfuse ATO/ATC Blade Fuses — 5 Pack (3 A to 20 A)$1.99 CAD
A latching switch to trigger the relay from the cabin. 3 amps is plenty for a relay coil.
Details for MTSW-1 Mini Toggle Switch (Pre-Wired)$2.99 CAD
Diodes, for when two triggers feed the same relay.
Details for 1 Amp Diodes PD-1A4 | 10 Pack$1.99 CAD
Cover the joints.
Details for 3M Super 33+ Electrical Tape, 75 Feet, 22.86 Meter Roll$15.98 CAD
Secure the new wiring. 1000 pack.
Details for 6" Wire Ties WT-6B | 1000 Pack$24.99 CAD
Your kit
Flat $10 shipping in Canada, free on orders over $200.
Rather we did it? We wire relays at our Markham shop: Book an installation
Power, ground and a turn-on wire for an amplifier, fused at the battery. Pick the kit by the wire size your amplifier's manual asks for.
Our pick: 4 gauge oxygen-free copper. 17 ft of power cable, ground, remote wire, ANL fuse holder and 250 amp fuse, loom and terminals.
Details for DB Link ME4K 4 Gauge Amplifier Installation Kit with OFC Copper Wire$199.99 CAD
Phoenix Gold's 4 gauge oxygen-free copper kit.
Details for Phoenix Gold ZRK20 4 Gauge Oxygen Free Copper (OFC) Amplifier Wiring Kit$179.99 CAD
Budget 4 gauge kit in copper-clad aluminum (CCA). CCA carries less current than copper of the same size; Phoenix Gold rates it for systems up to 1000 watts.
Details for Phoenix Gold ZXK20 4 Gauge Copper Clad Aluminum (CCA) Amplifier Wiring Kit$59.99 CAD
0 gauge oxygen-free copper, for big amplifiers or more than one.
Details for DB Link ME0K 0 Gauge Amplifier Installation Kit with OFC Copper Wire$319.99 CAD
17 ft 2-channel RCA cable, if your radio has RCA outputs.
Details for DB Link SX17 17 Foot 2 Channel RCA Cable$17.99 CAD
17 ft 4-channel RCA cable, for a 4-channel amp.
Details for DB Link SX417 17 Foot 4 Channel RCA Cable$38.99 CAD
Factory radio with no RCA outputs? This line output converter turns speaker wires into an RCA signal.
Details for Wavtech link2 Line Output Converter, 2 Channel$149.95 CAD
Delay ON timer relay, the usual fix for a pop when the amp turns on.
Details for Bueler BU510TD Time Delay ON Relay, SPDT, 12 Volt, 20/30 Amp$44.99 CAD
Ground more than one amp at one point: one 4 gauge in, four 8 gauge out.
Details for DB Link Nickel Ground Block NGB1448 / 1 x 4 gauge input 4 x 8 gauge output$14.99 CAD
Crimps 0, 2 and 4 gauge ring terminals.
Details for LY-IBHDCRIMP Heavy Gauge Hammer Style Crimp Tool$44.99 CAD
Cuts copper and aluminum cable up to 4 gauge.
Details for LY-206 Cable Cutter$19.99 CAD
Seals round the power cable where it passes through the firewall.
Details for ShopWorx DUM-DUM Butyl Rubber Tape, 3/8 inch Round Bead x 15 Foot Roll$28.99 CAD
Your kit
Flat $10 shipping in Canada, free on orders over $200.
Rather we did it? Amplifier installation at our Markham shop, from: One Channel Amplifier Installation $300 CAD
The tape, ties and small parts that go around a remote starter install. The starter, bypass module and T-harness depend on your vehicle: find them on our remote starter pages.
Most remote starters need vehicle-specific wiring and programming. If it's your first one, consider having us install it.
Wrap every new wire so it looks and sounds factory. What we use on our own installs.
Details for Tesa 51608 Fleece Harness Tape (Tearable) | Interior Use | 3/4" Width x 82 Foot Length Roll$13.99 CAD
Anchor the new harness to existing looms and brackets. 1000 pack.
Details for 8" Wire Ties WT-8B | 1000 Pack$34.99 CAD
Mount the control module so it lifts off for service.
Details for LY-VELCRO Velcro (Self Adhesive - 3 ft. long)$9.99 CAD
Cover every joint. Stays stuck in the cold.
Details for 3M Super 33+ Electrical Tape, 75 Feet, 22.86 Meter Roll$15.98 CAD
Self-adjusting stripper for 10 to 22 AWG.
Details for LY-731 Wire Stripper (Self Adjusting)$34.99 CAD
Get the dash panels off without marking them.
Details for LY-TPS5 Plastic Panel Puller and Scraper Set | 5 Piece Set$29.99 CAD
The hood safety switch: with the hood open, the car won't remote start. Check whether your kit includes one.
Details for HE-7846 Polycarbonate Hood Pin Switch$4.99 CAD
Keeps your OBD port free when a module or programming tool plugs into it.
Details for Accele OBD2T OBDII T-Harness$31.28 CAD
Your kit
Flat $10 shipping in Canada, free on orders over $200.
Rather we did it? Remote starter installation at our Markham shop, from: Remote Starter Installation $280 CAD
Finish a harness the way the factory does, seal it where it passes outside, and protect it from rodents.
Inside the cabin: tears by hand and stops rattles.
Details for Tesa 51608 Fleece Harness Tape (Tearable) | Interior Use | 3/4" Width x 82 Foot Length Roll$13.99 CAD
Under the hood: PET cloth that handles engine-bay heat and abrasion.
Details for Tesa 51036 PET Cloth Wire Harness Tape | Exterior Use | 3/4" Width x 82 Foot Length$12.99 CAD
BMW or Mercedes? Matches their factory interior tape.
Details for Tesa 51618 Fabric Harness Tape (BMW / Mercedes) | Interior Use | 3/4" Width x 82 Foot Length Roll$11.99 CAD
Capsaicin rodent tape, the same tape Honda sells as 4019-2317. Wrap it over wiring rodents can reach.
Details for Anti-Rodent Capsaicin Tape, 20 m Roll – Same Tape as Honda 4019-2317$62.99 CAD
Seals grommets and holes where wiring passes outside. Stays flexible.
Details for ShopWorx DUM-DUM Butyl Rubber Tape, 3/8 inch Round Bead x 15 Foot Roll$28.99 CAD
Keeps corrosion off connections, inside or outside the vehicle.
Details for Install Bay PZGGEL Anti-Corrosion Gel (For Electrical Connections)$19.99 CAD
11 inch ties for thicker looms. 100 pack.
Details for 11" Wire Ties WT-11B | 100 Pack$9.99 CAD
Your kit
Flat $10 shipping in Canada, free on orders over $200.
Rather we did it? At our Markham shop, from: Capsaicin Rodent Tape Wrapping $75 CAD
Prices and stock are live from the store. Not sure a part suits your vehicle? Text us at 647-439-4485
The supplies customers ordered most over the last year. Prices are live.
Most ordered
The Japanese-made tape Honda sells as part 4019-2317, on a 20 metre roll. It works on any vehicle.
Price $62.99
Best-selling relay
Delay OFF timer relay: keeps a circuit live after the trigger drops. Interior lights, fans, parking sensors.
Price $39.99
Pairs with most relays
The plug-in socket for a standard 5-pin relay, with 12 inch colour-coded leads.
Price $2.99
Most units sold
Plugs into a fuse slot and gives your new accessory a fused circuit of its own. Pick your fuse type on the product page.
$6.99 CAD
Fuse taps, relays, tape, ties, switches, diodes and resistors. Filter by type, brand or price.
Fuse taps, relays, harness tape, cable ties, switches and the small parts that make an install clean and reliable: the same supplies we use on our own installs at our Markham shop. Pick a job in the kit builder and it lists what you need, or shop by category. Flat $10 shipping in Canada, free on orders over $200.
A fuse protects the wire, so every power wire you add needs one, rated no higher than the wire can carry. A fuse tap does it at the fuse box: the car's original fuse goes in one slot and your new circuit's fuse in the other. Not sure which tap your fuse box takes? Our fuse identifier shows each type at true size.
Remote starter and alarm outputs, and small toggle switches, are made to switch a little current. For lights, horns, fans and door locks, let them trigger a relay and let the relay carry the load. A relay harness turns a bare relay into a plug-in part with colour-coded leads.
Tesa 51608 fleece tape is what we wrap interior harnesses in: it tears by hand and stops rattles. Tesa 51036 PET cloth tape handles engine-bay heat and abrasion, and Tesa 51618 matches the factory tape on BMW and Mercedes. Keep electrical tape, like 3M Super 33+, for covering joints rather than wrapping looms.
Pack DUM-DUM butyl round wires that pass through a grommet or a drilled hole, use a waterproof connector where a joint lives outside the cabin, and put anti-corrosion gel on connections that will see moisture.
Double-sided tape lets go of textured dash plastic on the first hot day unless you wipe the surface with 3M 4298 adhesion promoter first. Mount modules on hook and loop so they lift off for service, and tie new wiring to existing looms every few inches with cable ties.
Written by our installers. Free to use.
Match your fuse at true size on screen, with the colour code and the fuse tap that fits it.
Read a blown fuse the way we do: a clean break and a burnt one tell you different things.
Pick the job and get the diagram: every pin, the fuse and wire size, and the parts.
We hardwire dash cams and install remote starters, amplifiers, lighting and accessories at our Markham shop, and every install is backed by our lifetime installation warranty.
The one that matches the fuses in your fuse box: ATO/ATC, Mini, low-profile Mini, Micro2 or Micro3. Use our fuse identifier, or text us a photo of your fuse box and we'll tell you.
When the load is bigger than the switch or module output feeding it. The remote starter output, alarm output or toggle switch triggers the relay, and the relay switches the heavy current. Our relay wiring diagrams show how to wire one.
Inside the car, Tesa 51608 fleece tape: it tears by hand and stops rattles. Under the hood, Tesa 51036 PET cloth tape, which handles heat and abrasion. On BMW and Mercedes, Tesa 51618 matches the factory tape. Keep electrical tape, like 3M Super 33+, for covering joints.
Some supplies come that way: our 4, 6 and 8 inch cable ties are 1000 packs, and ATC and ATM fuse taps come in 50 packs. For larger quantities, text or email us.
Yes. We hardwire dash cams and install accessories, amplifiers, remote starters and alarms at our Markham shop, and every install is backed by our lifetime installation warranty. Book an installation.
Yes. Shipping is a flat $10 on orders under $200, and free in Canada on orders over $200. We also ship to the US and worldwide; US orders may be charged duties at checkout.
Tell us the job and the vehicle. We do this wiring every day, and we'd rather point you to the right part than have you order twice.