Parking Sensor Kits

Parking sensors measure the gap behind your bumper and beep faster as you close in. They're for the post, the bin and the bike you can't see over your trunk, and they retrofit to almost any vehicle. Buy the kit, or have it installed at our Markham shop.

Lockdown exclusiveTake the parking testBack into a garage blind, then try it with sensors.

Customers rate us 4.7/5 based on 1226 reviews.

How to buy parking sensors

  1. Rear, front or bothFour sensors cover one bumper. Eight cover front and rear.
  2. Beeps or a displayEvery kit beeps faster as you get closer. Display kits also show the gap.
  3. Installed in MarkhamAbout three hours for one bumper, or a full day for both. We call to book after checkout.

Our top 3 parking sensor kits

Our best sellers over the last two years, from lowest cost to full coverage. Take the parking test to hear the difference.

Lowest cost

KEETEC BS420

Four sensors for your rear or front bumper, and a beeper that speeds up as you close in. It can learn to ignore a tow bar or spare wheel.

Sensors
4, rear or front
Warning
Beeper
Shows the distance
No
Tow bar or spare wheel
Learns to ignore it
Front bumper
Needs the extension cable kit

Kit only $78.32

Installed $291.93

Kit $78.32 + installation $213.61

See the distance

KEETEC BS420LCD

The same four sensors, plus a display that shows the gap in metres. Worth it if you park close to a wall or another vehicle.

Sensors
4, rear or front
Warning
Beeper and display
Shows the distance
Yes
Good for
Tight garages and parallel parking

Kit only $106.80

Installed $320.41

Kit $106.80 + installation $213.61

Lockdown exclusive

The parking test

Something is behind you, and every round it’s somewhere new. Back up as close as you dare without hitting it. Try it with no sensors first, then with the beeper, then with the display.

Something is behind you. Back up as close as you dare.

Round 1

No sensorsJust you and the back window, like most cars without a kit.

Sensors

Your closest park

No sensorsNot tried
BeeperNot tried
Beeper + displayNot tried
  • From the driver's seat, anything lower than your back window can disappear
  • The BS420's beeps speed up as you close in and turn solid at about 30 cm
  • Display kits show you the gap in metres
  • We mount every sensor so it can't fall into the bumper

This is an illustration, not to scale. How much you can see out of the back depends on your vehicle.

0:18
Watch

Parking sensors save the supercar

Gary has to park in front of a $400,000 supercar. Turn the sound on.

All parking sensor kits

Kit only or with installation?

Free shipping in Canada on orders over $200. Worldwide delivery available.

Installed by our technicians in Markham, Ontario: about three hours for one bumper, or a full day for front and rear. We'll contact you to book a time after checkout.

  • Free shipping over $200
  • Worldwide delivery
  • Price match guarantee
  • Lifetime installation warranty
  • Car-wash-proof sensor mounting
  • 23 years, 100,000+ customers

KEETEC BS810LCD Front and Rear Parking Sensor Kit with 8 Sensors

$213.60

Kit only

Not included: Extension cables — $10.67 extra

$580.28 INSTALLED

Kit $213.60 + Extension cables $10.67 + install $356.01

KEETEC BS420LCD 4 Sensor Parking Sensor Kit, Dual Purpose Front or Rear Use

$106.80

Kit only

$320.41 INSTALLED

Kit $106.80 + install $213.61

KEETEC BS420 4 Sensor Parking Sensor Kit, Dual Purpose Front or Rear Use

$78.32

Kit only

$291.93 INSTALLED

Kit $78.32 + install $213.61

Rostra BackZone Plus 2501903BZP 4 Sensor Parking Sensor Kit

$142.40

Kit only

$356.01 INSTALLED

Kit $142.40 + install $213.61

Auto-i BSD1000P Ultrasonic Blind Spot Detection Kit with Rear Parking Sensors

$178.00

Kit only

$427.21 INSTALLED

Kit $178.00 + install $249.21

Our advice

How we mount the sensors

Sensors can be fitted two ways. Flush sensors clip onto a plate glued behind the bumper, so nothing sticks out. They look tidy, but automatic car washes work the clips loose, and once a sensor drops inside the bumper, the bumper has to come off to get it back.

We mount sensors from the outside, held by a flange behind the bumper. They sit very slightly proud of the surface, and they can't fall in or out. After two decades of installs, that's the trade we make every time.

About three hours for one bumper · A full day for both · Lifetime installation warranty

Watch out

What parking sensors can miss

Parking sensors bounce sound off whatever is behind you, so a few things can slip past them: thin things like a chain or a narrow pole, things lower than the sensors like a low curb, and anything tucked right under the bumper. Snow, ice or salt packed over a sensor can cause false alarms until you clear it, the same as your lights. Treat the beeps as a second set of eyes, and keep looking.

Not quite what you need?

Parking sensor questions

Will you have to drill my bumper?

Yes, for most kits. Each sensor needs a hole in the bumper, measured for height and spacing before it's cut, so the result is neat and even. We mount the sensors from the outside with a flange behind the bumper, so they can't fall in, even after years of automatic car washes. On trucks with steel or chrome bumpers, the Auto-i OEM-T401 mounts under the bumper instead, with no drilling.

Do I need front sensors, or just rear?

Most people start with rear, because that's where you're backing up blind. Front sensors earn their keep if you park nose-in a lot, drive something long, or have a low front bumper that meets curbs and parking blocks. If you want both, the eight-sensor KEETEC BS810LCD costs less than two four-sensor kits.

What's the difference between the display kits and the beeper kits?

Every kit beeps faster as you get closer. The display kits also show the actual gap in metres, so you can park within a few centimetres with confidence instead of creeping. The BS810LCD adds spoken warnings too.

How close can I get before it tells me to stop?

On the KEETEC BS420, the beeps speed up as you close in and turn into one solid tone at about 30 cm. That's the signal to stop. The display kits show the gap as you go. You can hear and see both in the parking test above.

How long does the installation take?

About three hours for one bumper, by appointment, and you'll have the vehicle back the same day. Front sensors can take a little longer, because the wiring has to run the length of the vehicle. For front and rear together, plan to leave the vehicle with us for the day.

Will a tow hitch or bike rack set it off?

It can. Anything fixed within range of the sensors looks like an obstacle. The KEETEC BS420 can learn to ignore a tow bar or spare wheel, and we set every system up around your hitch during the install, so mention it when you book.

Do parking sensors work in winter?

Yes. Snow, ice or salt packed over a sensor can cause false alarms or block it until you clear it, the same as your lights, and a quick wipe fixes it. The KEETEC BS420's sensors are rated down to −40°C.

Will this work on my vehicle?

In almost every case. These are universal kits: the sensors go in a standard plastic bumper and the control module wires into your reverse light, so they don't depend on your vehicle's factory electronics. Metal bumpers, heavy aftermarket bumpers and some fibreglass panels need a conversation first. Send us your year, make and model if you're not sure.

What's in the box? Do I need anything else?

Each kit comes with its sensors, control module, beeper or display, and wiring, and nothing else is needed for a rear install. Fitting the BS420 in a front bumper needs the extension cable kit. The BS810LCD's installed price already includes it.

Can I install it myself?

Plenty of customers do. Expect to take the bumper cover off, drill and mount the sensors, and run wiring to your reverse light and into the cabin for the beeper or display. Budget a few hours and be comfortable with basic 12V work. Every kit ships with instructions, and our support team can help by phone.

Will it drain my battery?

No. Parking sensors only draw power when the vehicle is running, and rear sensors switch on when you select reverse. Everything shuts down with the ignition.

Will it affect my vehicle warranty?

A parking sensor kit connects to a couple of your vehicle's circuits, usually the reverse light and ignition, so connections are made. We make them to factory wiring standards and can document what was added and where. A manufacturer generally can't void your whole warranty over an aftermarket accessory; the usual position is that they'd need to show it caused the specific failure. If your vehicle is under warranty and you're concerned, ask us before you book.

Not sure which kit you need?

Send us your year, make and model and tell us where you park. We'll recommend a kit and give you the installed price.