CompustarCM900AS

The alarm and remote start control module used in the Compustar CS7900AS. For automatic transmission vehicles. Master guide, feature tables and setup help, including the alarm LED codes.

Status
Current model
Documents
4 current, 2 older
CM900S and CM900AS master guide
v1.32, May 2026 edition

Manuals and guides

For owners

  • FT-KP2 touchpad programming and operation Programming guide, PDF, Version 1.0

For installers

Wiring, programming and install detail for technicians and experienced DIY installers.

  • CM900S and CM900AS master guide Installation guide, PDF, v1.32, May 2026 edition
  • CM900S and CM900AS feature tables Option settings reference, PDF, v1.32, May 2026 edition
  • DRONE KL1 KeyLocker installation guide Installation guide, PDF, Guide version 2.0
Replaced

Older versions

CM900S and CM900AS master guide, v1.32, March 2025 editionEarlier edition. Feature 4-3 (Aux 1 output) options differ from the May 2026 edition.
View
CM900S and CM900AS feature tables, v1.32, March 2025 editionEarlier edition. Feature 4-3 (Aux 1 output) options differ from the May 2026 edition.
View
Setup help

Program a remote to the CM900

Remotes have to be programmed before the system does anything. The CM900 holds 4 remotes. If you only have 2, program each one twice.

  • 1. Cycle the keyTurn the key between ON and OFF 5 times within 10 seconds. The parking lights flash once.
  • 2. Tap LOCKWithin 2 seconds, tap LOCK on the remote (a quick half-second press). The parking lights flash once.
  • 3. More remotesTap LOCK on each other remote the same way, up to 4.
  • 4. DoneThe parking lights flash twice when programming ends.

Push-to-start: press the start button to ON (don't start), back to OFF within 5 seconds, then to ON again within 5 seconds. Press the brake 3 times within 5 seconds: the parking lights flash once. Tap LOCK on each remote (one flash each). It leaves programming on its own after 10 seconds with no remote.

More answers for the CM900AS

Automatic transmission vehicles only

The CM900S and CM900AS are made for automatic transmission vehicles only. There's no manual transmission loop in the module. For a manual transmission vehicle, choose another remote starter or submit a support ticket and we'll point you to one that supports it.

CM900AS alarm: what the LED tells you

After you arm, the blue LED stays on for about 25 seconds while the shock sensor settles. Once it starts flashing, the sensors are ready. After the alarm goes off, the LED flashes to show what set it off:

  • 2 flashesDoor
  • 3 flashesShock, stage 1
  • 4 flashesShock, stage 2
  • 5 flashesTilt
  • 6 flashesIgnition turned on
  • 7 flashesHood
  • 8 flashesTrunk
  • 9 flashesExtra sensor, stage 1
  • 10 flashesExtra sensor, stage 2

Too sensitive? The FT-Shock II sensor has a dial from off and 1 (least sensitive) to 10 (most sensitive). Turn it down a step at a time.

Valet mode

Valet mode turns off remote start and the alarm. Keyless entry still works. If you try to remote start in valet mode, the parking lights flash 3 times and then 10 times.

  • Turn it on: brake and keyHold the brake and turn the key ON and OFF 5 times within 10 seconds. The parking lights flash once.
  • Turn it on: 4-button remoteWith the key ON, press LOCK and TRUNK together for half a second. The parking lights flash once.
  • Turn it off: no remoteTurn the key ON and press the brake 10 times within 10 seconds. The parking lights flash twice.
  • Turn it off: 4-button remotePress LOCK and TRUNK together for half a second. The parking lights flash twice.

With DroneMobile: in the app, open Settings, Vehicles, your vehicle, System, switch Valet on or off and tap Save. 3- and 5-button remotes have their own steps: see the remote's manual.

Remote start didn't work? Read the flashes

When a remote start fails, the parking lights flash 3 times, pause, then flash a code. 2-way remotes show “Start Err” and the number.

  • 1The engine is already running, or tach hasn't been learned.
  • 2Key is in the ON position.
  • 5The brake pedal is pressed.
  • 6The hood is open.
  • 8Tach or tachless sensing failure.
  • 10The system is in valet mode.

Started, then shut off? The parking lights flash 4 times, then a code: 1 lost engine sensing, 2 lost parking brake signal, 3 brake pedal pressed, 4 hood pin triggered. To show it again, tap button 4 on a 2-way remote, or hold TRUNK and START together for 2.5 seconds on a 1-way remote.

Tach learning (installers)

The CM900 comes set to tachless. To use tach mode, learn tach before the first remote start: start the vehicle with the key, hold the brake, then send a remote start. One chirp and one parking light flash means tach is learned. Two chirps and three flashes mean the module didn't see a usable tach signal.