KEETECBS420LCD

KEETEC's 4-sensor parking sensor kit with a distance display and voice alerts, for the front or rear bumper. User guide, settings, testing and fault help.

Status
Current model
Documents
1 current
Sold as
BS420LCD

Manuals and guides

For owners

  • BS420LCD user and installation guide Owner's manual, PDF
Setup help

When the sensors come on

Rear sensors come on by themselves when you shift into reverse and turn off when you shift out. Front sensors come on when you press the brake and stay on for a few seconds, so they're working as you creep forward into a spot.

The closer you get, the faster the beeps. At about 30 cm they turn into a solid tone: stop there.

More answers for the BS420LCD

Test the sensors after installing

Test before you rely on it. You need a helper and something flat, like a sheet of plywood about 30 cm by 1 m.

  1. Park somewhere with nothing behind you, start the vehicle and shift into reverse. It should beep once (or show a clear display) to say it's working.
  2. Have your helper stand the board up about 2 m behind the bumper, then walk it slowly toward the vehicle. The warnings should speed up as it gets closer.
  3. Repeat behind each corner and the middle, so you know every sensor sees.
  4. Front sensors: press the brake to wake them up, then do the same in front of the bumper.

A sensor that never reacts is usually unplugged, or aimed at the ground. Check its plug at the control unit first.

Teach it to ignore a tow bar or spare wheel

If a tow bar, bike rack or rear spare wheel sets the sensors off every time, the kit can learn to ignore it. Do this somewhere with nothing else behind the vehicle, with the tow bar or rack fitted.

  1. Turn the ignition on.
  2. Shift from Neutral to Reverse 10 times, each change within about a second.
  3. On the 10th time, leave it in Reverse. It beeps to confirm it has learned.

To clear it, do the same thing 12 times. If you lose count, leave it in Reverse for 2 seconds and start again. Front kits on the BS420 and BS420LCD learn a bull bar the same way, but by pressing and releasing the brake 10 times instead.

Turn the voice off or change the volume

Both are set with the SET button on the display, with the ignition on and the vehicle in reverse.

  • Volume: press SET to step through 1 (low), 2 (medium) and 3 (high). It saves on its own after a few seconds. It always goes to full volume under 30 cm.
  • Voice: hold SET for 2 seconds, then press it to switch between 01 (voice on) and 00 (voice off). The beeps keep working with the voice off.
Three short beeps when it comes on

Each time it comes on, the kit checks all four sensors. Three short beeps means one of them didn't answer. The BS420LCD's display also shows which one.

  • Clean the sensors. Ice or packed snow can make a sensor look dead.
  • Check the sensor plugs at the control unit. They're labelled A to D and must go in the matching sockets.
  • Still beeping three times? The sensor probably needs replacing. Submit a support ticket and we'll sort it out.
Mounting the sensors in the front bumper

The sensor cables are 2.3 m long, which is plenty for a rear bumper with the control unit in the trunk. In the front bumper the control unit sits much further away, so you'll need the extension cable kit, which takes each sensor cable to 4.6 m.

On the BS420 and BS420LCD, move the jumper on the control unit to F before installing. Front sensors come on when you press the brake, not when you shift into reverse.

False alerts in rain, snow or slush

Ultrasonic sensors need a clean face to work. Heavy rain, ice, slush, mud or a layer of road salt can make them beep at nothing, or miss things. Wipe them with a soft cloth or rinse them with low-pressure water. Don't blast them with a pressure washer up close or scrape them, and melt off ice rather than chipping it.

Rough ground, tall grass, and steep driveways can also set them off. If one sensor keeps alerting on a clean, dry day, it may be loose or aimed too low: submit a support ticket and we'll check it.

Setup video

From the Lockdown Security YouTube channel