iDatastartRemotes

• The install has to be finishedThe control module's own programming, including tach programming, has to be done before any remote is paired. That's done when the system is installed.
• The module is set for one brand of remoteThe module is set up in Weblink for the brand of remote it uses. If it was set up for a different brand, the remote won't pair, and an installer needs to change that.
• Up to four remotesThe system holds a maximum of four remotes.
• Don't start the engineEvery method uses the ignition ON position. Leave the engine off.

• 1. Ignition ONTurn the ignition to ON. Don't start the engine.
• 2. Press, then hold, the antenna buttonPress and release the button on the antenna, then press and hold it. The antenna's lights turn solid blue and the parking lights flash once.
• 3. Press LOCK on each remoteStill holding the antenna button, press LOCK once on each remote. The antenna's lights flash blue once for each remote paired.
• 4. Release the antenna buttonThe antenna's lights turn off.
• 5. Ignition OFFTurn the ignition off, then test every remote.

To pair a remote as the second vehicle: do steps 1 and 2 of the antenna button method. Then, instead of pressing LOCK alone, press F twice and LOCK once on the remote. Finish with steps 3 to 5: the antenna flashes blue once, release the antenna button, then turn the ignition off.

• 1. Ignition ONPress the start button to ON. Don't start the engine.
• 2. OFF within 5 secondsWithin 5 seconds, press it to OFF.
• 3. ON again within 5 secondsWithin 5 seconds, back to ON. Don't start the engine.
• 4. Brake three timesWithin 5 seconds, press the brake pedal three times. The parking lights flash once: the system is ready for your remotes.
• 5. Tap LOCKTap LOCK on the remote, a quick half-second press. The parking lights flash once: the remote is accepted.

Pair any other remote within 5 seconds. After 5 seconds with no remote pressed, the system leaves programming on its own.

For another brand's remote, on an iDatastart module set up in Weblink for that brand. Up to four remotes. Each step has a time limit, so read them through first.

• 1. Cycle the ignitionWithin 7 seconds, turn the ignition OFF and ON five times, quickly. The parking lights flash once.
• 2. Press LOCKWithin 5 seconds, press LOCK once on the remote. The parking lights flash once.
• 3. More remotesRepeat step 2 with each remote, each within 5 seconds of the last.
• 4. FinishWait for the parking lights to flash twice, then turn the ignition off.

• Let go of the antenna button too soonWith the antenna button method, keep holding the button until every remote has been paired.
• Too slowThe push-to-start and non-iDatastart methods have 5 and 7 second limits. Start again from step 1.
• Module set for another brandIf the module was set up in Weblink for a different brand of remote, an iDatastart remote won't pair. An installer needs to change it.
• Already four remotesThe system holds four remotes at most.
• Weak batteryPut a fresh battery in the remote and try again.

Remotes on the AN2300A antenna: TR1110A and TR1150A (FCC ID 2AEPJ1150A), TR2310A and TR2350AC (FCC ID 2AEPJ2350A).

LoRa remotes on the AN2400A antenna: TR2410A, TR2650A, TR3450AE, TR3450AF, TR4450AC and TR4650A.

RF kits, which come with remotes and an antenna: RF1111A, RF1151A, RF2312A and RF2352A on the AN2300A, and RF2412A and RF4652AE on the AN2400A. The antenna has to be installed before the remotes can pair.